NMI Not Accepting Payments
NMI Not Accepting Payments Here’s how to reset (reboot) your NMI/BBPOS Chipper or 2X BT card reader 🔁 1. Soft (Power Button) Reset Hold down the power button for about 10 seconds until the LED turns off and the device reboots. Once it powers back on, it will reconnect automatically. This resolves most minor connectivity […]
Disconnected / Not Connected to POS
Disconnected / Not Connected to POS Here’s how to reset (reboot) your NMI/BBPOS Chipper or 2X BT card reader: 🔁 1. Soft (Power Button) Reset Hold down the power button for about 10 seconds until the LED turns off and the device reboots. Once it powers back on, it will reconnect automatically. This resolves most […]
How to show IP address on Pax (Ethernet)
How to show IP address on Pax (Ethernet) 🔧 Method 1: Using the Hidden Corners (Diagnostic Menu) 💡 Works on: A920, A80, A35, and many other PAX models From the home screen, tap all four corners of the screen in clockwise order: Top-left → Top-right → Bottom-right → Bottom-left (Do this quickly within 5 seconds) […]
Part of Pax Terminal
Part of Pax Terminal PAX A920 PAX A35 Pax Cord Long thick cord. Plug this cord into the back of the PAX device. Short cord with Red Plug. If your site uses Ethernet, plug the Ethernet cord into this cord’s red plug. Long thin cord with VGA Plug type. Not used. Long thin cord with […]
Error code on Pax
Error code on Pax ✅ Issuer / Transaction Response Codes (00–99) These standard codes come directly from the card issuer: 00 – Approved 01 – Refer to issuer 05 – Do Not Honor 12 – Invalid Transaction 13 – Amount Error 14 – Invalid Card Number 15 – No Such Issuer 16 – Insufficient Funds […]
⚠️Enable Tip on Pax Device – Troubleshooting Guide
⚠️ Enable Tip on Pax Device – Troubleshooting Guide Step1. Go to Cliqbux POS and login your pin Step 2. Go to settings > Payments Step 3. Enable “Enable Tip Collection From the Pax Device”
How to close Batch using Pax
How to close Batch using Pax 🧾 Steps to Close Batch on PAX Terminal IF you are on cliqbux screen just do 4 corners 3 times first (Clockwise) You will be prompted to enter a password 👉 Enter today’s date in MMDDYYYY format (e.g., for June 13, 2025 → 06132025). Once inside, tap Host Settings. […]
How to Connect a PAX Device via Bluetooth
How to Connect a PAX Device via Bluetooth Applies to PAX models like A920, A80, A35, etc. 🔧 Step 1: Open Bluetooth Settings From the Home screen, tap the Settings icon (⚙️). If prompted, enter the admin password (e.g., 9876 or pax9876@@). Go to Bluetooth. 📲 Step 2: Enable Bluetooth Toggle Bluetooth ON (if it’s […]
How to Connect a PAX Device via Wi-Fi
How to Connect a PAX Device via Wi-Fi 🔧 Step 1: Open Settings From the Home screen, tap the gear icon (⚙️) or swipe down and tap Settings. Enter the admin password if prompted (Common defaults: 9876, pax9876@@, or your custom PIN). 📡 Step 2: Enable Wi-Fi Tap “Wi-Fi” under the Network section. Toggle the […]
PAX Device Not Responding / Freezing – Solutions
PAX Device Not Responding / Freezing – Solutions Solution 1 – Soft Restart (Reboot the Device) Steps: Press and hold the Green (✔️) and Red (❌) buttons simultaneously. Keep holding until the screen goes black and the device restarts. Wait for the device to fully reboot. 📝 This works on most PAX models (like A920, […]
